GYEON Q²M CeramicDetailer Ceramic Quick Detailer 1000ml

SiO₂ care between washes with the GYEON Q²M CeramicDetailer

What is the GYEON Q²M CeramicDetailer? An SiO₂-enriched quick detailer that tops up coatings and sealants between washes — hydrophobics, gloss and dirt resistance in one pass. Not a coating replacement, not a long-term sealant, and not meant for heavily soiled surfaces.

GYEON Q²M CeramicDetailer is an SiO₂-based quick detailer from GYEON built specifically for ceramic-coated cars. The silicon dioxide particles inside react with the existing coating and boost its water beading on the spot, in a measurable way — at the same time a temporary protective layer goes down that makes dust and dirt stick less. Unlike classic quick detailers that only polish things up optically, the CeramicDetailer lays down real, if time-limited, protection.

• Hydrophobics back in 2 minutes. Once you've sprayed it on and buffed it off, water beads sharply again straight away — even when the coating has been fading for weeks. The effect holds up to 6 weeks, depending on weather and where the car sits. On garaged cars, often a good bit longer.
• 40–50 ml per car, 500 ml covers 10–12 applications. With that kind of yield, the CeramicDetailer is one of the most economical SiO₂ detailers around. One spray per panel does it — lay down more and you don't get a better effect, just more buffing.
• Works wet or dry, and as a drying aid too. Sprayed onto wet paint after the wash, the CeramicDetailer speeds up drying and leaves a protective layer at the same time. On dry paint it pulls off dust and fingerprints without scratch risk — as long as the surface isn't heavily soiled.

Detailing1's tip from the shop: The most common mistake with the CeramicDetailer: spraying on too much product at once. A single spray per body panel is enough. Lay down three or four sprays and you'll be fighting streaks afterwards — not because the product is bad, but because excess SiO₂ smears across the surface during buffing instead of soaking in. Below 5 °C we'd recommend using the product in the garage at room temperature, since cold makes it harder to spread and leaves streaks.

Using CeramicDetailer right on wet and dry paint

The two-towel method is a must with the GYEON Q²M CeramicDetailer — one soft microfibre to spread, a second to buff off. Work with just one towel and you smear loosened dirt and SiO₂ residue across the paint, creating exactly the streaks that then get wrongly blamed on the product.

On dry paint: one spray per panel straight onto the paint or onto the microfibre, spread it evenly, then buff with the dry side of the second towel. Don't work in direct sun — otherwise the product flashes off within seconds and is hard to wipe away cleanly after that.

In the shade or in the garage the job is far more relaxed. With a light dust film after 3–5 days of standing, the CeramicDetailer is all the care you need between washes — a full wash isn't necessary then. For best results use a short-pile microfibre at 300–400 GSM — long-pile towels grab too much product and cut the effect on the paint.

On wet paint right after the wash: 2–3 sprays per panel onto the wet surface, then pull it off in straight lines with a drying towel. Here the CeramicDetailer works as a drying aid — the water gets soaked straight into the towel instead of smeared, and the SiO₂ protective layer builds in the same pass. On the weekend wash this method saves you a good 10 minutes over drying separately and then sealing.

Important with both methods: give the bottle a quick shake before use. The SiO₂ particles settle at the bottom over time — spray without shaking and that first spray lays down nothing but carrier, no active. That's also why some people see less gloss on the first panel than on the last.

6 weeks of durability and where the limits are

Under ideal conditions — garaged car, no constant wet, no winter duty — the CeramicDetailer holds up to 6 weeks. In daily life with an outdoor spot, rain and the odd car-wash run, 3–4 weeks is more realistic. That's no flaw, it's exactly what you'd expect from a quick detailer — products in this class are built for fast top-ups, not for longevity.

The instant hydrophobic reactivation is the real strength: within seconds of buffing off, water beads visibly and runs off fast, dirt sticks less, and dust pickup drops noticeably thanks to the antistatic effect. On dark paint especially that's a win, because dust shows up faster there. On glass and wheels the CeramicDetailer works too — though durability there is shorter than on paint, in our experience 2–3 weeks rather than 6.

Where the CeramicDetailer isn't the right product: on uncoated paint it does a lot less, because the SiO₂ particles find no existing coating to chemically grab onto — the effect fizzles out there after a few days. It's not built for heavy soiling like bug splatter, tar or bird droppings: wash that off with a car shampoo first, then apply the detailer. On matt or satin paint and wraps it must not be used, since SiO₂ creates unwanted gloss there.

If you need real protection with 3+ months of durability, reach for the Q²M Cure spray sealant. When fast top-ups for the next few weeks are all you're after, the CeramicDetailer is the time-saver — 2 minutes instead of 15.

CeramicDetailer or Cure for your coating

Both GYEON products top up coatings, but with fundamentally different effort and a different result. Get the difference and you save money and time.

Q²M Cure is a full SiO₂ spray sealant with a higher active concentration. It builds a measurably thicker protective layer that holds 3–6 months and substantially regenerates the coating. The downside: Cure needs clean, ideally degreased paint and more care when you apply it — on slightly dirty paint on a Thursday evening, Cure is overkill. The CeramicDetailer, on the other hand, goes on in 2 minutes, forgives more mistakes and covers the weeks between Cure top-ups.

The ideal routine for coated cars looks like this: Cure every 2–3 months as base protection after a thorough wash, CeramicDetailer weekly or as needed for a quick top-up in between. That keeps the coating in top shape for good, without you putting in 30 minutes every week. The weekly CeramicDetailer pass costs you 2 minutes per car.

If you've got no coating on the paint and you're after real long-term protection, the CeramicDetailer alone is the wrong call. Here it's worth starting with a proper ceramic coating like Q² Mohs EVO or Q² Pure EVO, followed by CeramicDetailer as your maintenance product. The combo of coating and regular detailer is what GYEON designed as a closed care system. Day-to-day, that system works better than any single product, because each part covers the other's weak spots: the coating delivers the base hardness, the CeramicDetailer the ongoing freshness.

To get started we'd recommend the 500 ml bottle — it covers 10–12 full car applications and shows you within 2–3 weeks whether the CeramicDetailer fits your care routine. The 1-litre bottle pays off if you run the detailer regularly every week or look after several cars.

Application of GYEON Q²M CeramicDetailer

How to refresh your ceramic coating in 2 minutes

One spray per body panel is enough — whether on wet or dry paint. Distribute the product with a short-pile microfiber towel (300–400 GSM) in straight, overlapping passes. Do not work in circular motions, as this can create holograms on sensitive paintwork.

Buff with a second, dry microfiber towel. The two-towel method is mandatory with CeramicDetailer: a single towel will smear excess SiO₂ instead of absorbing it. If you use a waffle weave towel for drying, you can use CeramicDetailer directly as a drying aid — 2–3 sprays per panel on wet paint and immediately wipe off with the drying towel.

The order matters: roof first, then hood, sides, and finally the bumpers. This prevents already treated areas from being double-coated by overspray when working on higher panels. An entire vehicle can be completed in under 2 minutes.

For best results, use CeramicDetailer every 1–2 weeks after a regular wash. This keeps the ceramic coating at maximum performance level permanently and significantly extends the intervals between professional re-coatings.

Notes: Do not use in direct sunlight or on hot paint — SiO₂ bonds too quickly and leaves dull spots. Work in the shade at temperatures above 30 °C or wait until the evening. CeramicDetailer also works on glass and wheels, but the durability there is shorter (2–3 weeks instead of 4–6 weeks on coated paint). Store frost-free between 5 and 30 °C, shelf life 24 months after opening.