ZviZZer Thermo Velour Pad Thermo Velour Pad (Orange) 1 piece

Build even, deep gloss with no holograms

What is the ZviZZer Thermo Velour Pad? A finishing pad with a dense, very fine velour pile fabric over open-cell thermo foam, hook-and-loop backed, in the Orange colour system. It builds deep, even gloss and barely cuts any material at all. Not for removing scratches or swirls, and not for heavy correction on neglected paint.

ZviZZer Thermo Velour Pad is a velour polishing pad from ZviZZer for the finishing step, listed as Orange in the colour system. Instead of a plain foam head, a dense, short-pile velour fabric sits over the open-cell thermo foam. That fine fibre surface spreads the polish very evenly and works it out streak-free, so you get a deep, uniform gloss. Self-cut is low, so the velour pad refines rather than removes material. It runs on hook-and-loop on a matching backing plate.

• Velour for an even, hologram-free finish. The dense, very fine pile fabric spreads the finishing polish across the whole panel and works it out streak-free at about 1,500 rpm. That way the velour pad pulls out the last 5 to 10 percent of depth without setting the fine holograms a too-grabby foam pad leaves on soft paint.
• Five sizes from 40 to 160 mm. The pad comes in 5 diameters: Ø 40, 60, 80, 130 and 160 mm, 1 piece each. The big 130 and 160 mm are for bonnets, doors and roofs, the small 40 to 80 mm for pillars, bumpers and tight spots. A 15 mm build height keeps the pad flat and easy to control.
• Low self-cut, lots of gloss. The velour pad is a pure finishing and sealing pad with nearly 0 mm self-cut. So it's not just for buffing out, but also for laying down sealants and liquid waxes evenly in a single pass. The harder pads give you the cut, this one gives you that last percent of depth.

Detailing1's tip from the shop: The most common mistake with a velour pad is treating it like a foam pad and running it with loads of product and high speed. The pile fabric then soaks up and smears the polish instead of working it out, and leaves a haze. Little product, medium speed, light pressure. On a dark Audi A4 with 2026 paint we used the velour pad after polishing to even out the gloss where the grabbier pad still left fine streaks sitting in the reflections.

Little product, medium speed, work it out streak-free

You bring in the velour pad after the actual polishing step: a little finishing polish on the dry pile fabric, spread it at medium speed and work it out with light pressure until the film goes clear.

Day-to-day, the orange ZviZZer velour pad is the partner of a fine finishing polish like the green UC 1000 Ultrafine Cut. You drop a pea-sized amount on the pad, spread it at around 1,000 rpm, then work it out at about 1,500 to 1,600 rpm with light pressure. The velour lays the polish down evenly and finishes it streak-free. To lay down a sealant, you go one notch slower again and with less pressure.

Keep the pile fabric clean: knock the pad out after two or three sections, a clogged velour won't take any more polish and just smears. Keep pressure and speed low, because the fine fibre surface builds heat fast with too much friction. The coarse groundwork is handled by the polishing pads with foam or wool.

Deep gloss yes, removing scratches no

The velour pad builds gloss and evens out the finish, but it corrects nothing: it lacks the cut for removing scratches, swirls and holograms.

Its home turf is the last step of a detail: paint that's already polished and needs maximum depth and an even, hologram-free gloss. That's exactly where the dense velour shines. Laying down sealants, glazes and liquid waxes also goes more evenly with it than by hand, because the pile fabric spreads the product thin and streak-free.

The limits are clear. If the paint has swirls or dull patches, a correction step belongs before it: for the cut you grab a grabby Nano Wool Pad or a foam pad with cutting polish, and only then does the velour pad come in for the finish. If you're after cut, wool or foam is right. If you're after deep gloss, velour is right. And a pad alone refines nothing, the gloss only comes from velour and a fine polish working together.

For the finish, not for correction

The ZviZZer velour pad is the right call when, after polishing, the last percent of depth and an even gloss across the whole panel are missing.

It's less suited as the only pad for a whole detail, because with no real cut it corrects no defects. It's the finishing partner of the grabbier pads, not their replacement. So anyone who polishes regularly keeps at least one velour pad in the right size to hand next to the foam and wool pads. Because it cuts so little, it spares the thin clear coat, which loses a few microns with every polishing pass.

One detail that decides how long it lasts and that most people overlook: wash the pile fabric out before the polish hardens in it, and let it air-dry lying flat, not in the sun. Hardened polish residue glues the fine velour fibres together, then the pad lays the polish down unevenly and exactly the velour's advantage, that streak-free finish, is lost. Kept clean, the fibre surface stays soft over many details.

Using the ZviZZer Thermo Velour Pad

Uniforming the gloss streak-free after polishing

The Velour Pad is the final step: It is used once the paint has already been polished with a foam or wool pad and only maximum depth and an even gloss across the entire surface are missing. Attach the pad to a suitable backing plate using the hook-and-loop fastener.

Apply a pea-sized amount of a fine finish polish to the dry velour fabric, distribute it at around 1,000 rpm, and then work it in at approximately 1,500 to 1,600 rpm with light pressure until the polishing film becomes clear and a high gloss is achieved. The dense pile fabric lays down the polish evenly and finishes streak-free.

Work in sections and tap out the pad after two to three sections; a clogged velour will no longer absorb polish and will only smear. The heavy preliminary work is done by the effective polishing pads made of foam or wool. For an even application of a sealant or liquid wax, proceed even more slowly and with less pressure.

Wash out the pile fabric immediately after polishing, before the polish hardens inside it, and let it air dry lying flat, not in the sun. This keeps the fine velour fibers soft and ensures an even application of gloss for the next detailing job.

Notes: The Velour Pad is purely a finishing and sealing pad and removes almost no material. It does not remove scratches, swirls, or holograms; for that, you should use an effective wool or foam pad with a cutting polish beforehand. Rule of thumb: If you are looking for cut, use wool or foam; if you are looking for high gloss, use velour. A pad alone does not refine anything; the gloss is only created in combination with the fine polish. Keep pressure and speed low, otherwise the fine fiber surface will build up heat. Store in a dry and clean place; protect the velour from solvents and harsh cleaners.